Skip to main content

BEKO Dishwasher Error Codes

 BEKO Dishwasher Error Codes

Error CodesMeaning
H2Turbidity sensor error
H3Diverter valve error
H4NTC error
H5Uninterruptible water inlet error
H6Water inlet fault
H7Heating fault
E01No rinse.
E02Water drainage anomaly.
E03Boiler temperature reset anomaly.
E04Water filling anomaly.
E05Tub thermometer anomaly. (Probe open)
E06Tub thermometer anomaly. (Probe shorted out)
E07Boiler thermometer anomaly. (Probe open)
E08Boiler thermometer anomaly. (Probe shorted out)
E09Boiler loading time out
ESFElectro-mechanical safety device
ESLIncorrect tub level:
E22Tub heating time out
BEKO Dishwasher Control Panel
BEKO Dishwasher Control Panel

Troubleshooting

Before calling service check the following & Trouble shooting guide supplied on the following page.

Symptoms: Spotting / filming / poor cleaning results

Possible Causes:

  1. Insufficient amount of detergent.
  2. Hard water.
  3. Spray arms need cleaning.
  4. Improper loading.
  5. Insufficient water fill.
  6. Filter system needs cleaning.
  7. Oversudsing – Prewashing with a liquid dishwashing detergent.

Solutions:

  1. Increase the amount of detergent, especially when washing full loads, or in hard water.
  2. Increase water softener dosage. Use additional detergent, increase rinse agent dosage.
  3. Check the nozzle holes in the spray arms. They may be blocked with a soil particle. Check and clean them periodically.
  4. Follow instructions for use for proper loading procedures. Place dishes so water spray reaches all soiled surfaces. Do not overcrowd the baskets since this will block the water spray.
  5. Check mains water pressure.
  6. Remove any accumulated or deposited foods. Check and clean them periodically.
  7. Rinse items thoroughly before putting them in the dishwasher to remove dishwashing detergent.

Symptoms: Small particles (food or detergent) left on items

Possible Causes:

  1. Water not reaching surfaces, dishwasher overcrowded.
  2. Insufficient water fill.
  3. Powder detergent stored too long or under adverse conditions
  4. Rinse aid supply depleted.

Solutions:

  1. Check to be sure water action is not blocked by dishes. Check filter system for accumulated or deposited food or detergent. Load dishwasher correctly. Keep filter system clean.
  2. Check mains water pressure
  3. Use powder detergent within one to two months after purchase. Open one box at a time. Always close pouring spout after each use. Store in a cool, dry place.
  4. Add rinse aid to the dispenser.

Symptoms: Pitting of stainless steel items

Possible Causes: Prolonged contact with salty or highly acidic foods or with undissolved or highly concentrated detergent.

Solutions: Remove spots with silver polish. Rewash. Wash soon after use, or pre-wash items if they will not be washed right away. Do not overload cutlery basket. Avoid spilling or pouring detergent directly on flatware. Make sure dispenser cup is properly closed.

Symptoms: Dishes not dry

Possible Causes:

  1. Improper loading.
  2. Rinse aid supply depleted.

Solutions:

  1. Load so that all items are properly tilted for good drainage. Avoid nesting of dishes and/or silverware.
  2. Add liquid rinse aid.

Symptoms: Scratches on glassware

Possible Causes: A water or chemical reaction with some glassware. Usually caused by some combination of soft or softened water and alkaline washing solutions reacting with the glassware. Can be accelerated by poor rinsing, overloading and excessive temperature.

Solutions:

  1. The condition may not always be preventable. To minimize the possibility of etching, use minimum amount of detergent.
  2. Use of the appropriate programme.
  3. Use of a rinse aid may also help.
BEKO Dishwasher Digital Panel
BEKO Dishwasher Digital Panel

Symptoms: Detergent cakes in detergent dispenser.

Possible Causes:

  1. If using powder detergent, there may be dampness in the dispenser.
  2. If using gel detergent, the detergent may be left in dispenser too long before using.
  3. Faulty cover.
  4. Improper loading.
  5. Old detergent.

Solutions:

  1. Make sure dispenser is dry before adding powderdetergent. Start dishwasher immediately.
  2. Start dishwasher soon after adding gel detergent. Do not allow detergent to dry out in dispenser.
  3. Do not overfill. Cover should close tightly. Checkcover for fit.
  4. Do not place large items in front of dispenser.
  5. Use detergent within one to two months of purchase. To assure freshness, buy detergent as needed and no more than one or two at a time. Store in a cool, dry place.

Symptoms: Chipping and breakage of dishes/glasses.

Possible Causes: Improper loading.

Solutions: Load with care following the instructions for use. Place glassware so it does not touch the other dishes. Remove from dishwasher carefully.

Symptoms: Odour in dishwasher

Possible Causes:

  1. Dishes washed only every two or three days.
  2. A dirty filter system may contribute to a bad odour.

Solutions:

  1. Use the pre-wash cycle at least once a day until a load accumulates, or hand rinse dishes before loading dishwasher.
  2. Clean filter system.

BEKO Dishwasher Manual PDF

Comments

Post a Comment

Popular posts from this blog

LG Dishwasher Error Codes

  Troubleshooting according to displayed error message: Error Message Meaning 2H Estimated Time. A 2H is only an indicator of the estimated time remainging for cycle. 2H means the estimated time remaing is less than 2 hours, when the time is less than 99 minutes, is starts counting down untill the washing cycle is over. This is not an error code and does not require a repair service. AE AE Error code indicates a possible leak from the unit. This is most often caused by excessive suds overflowing into the base of the dishwasher. Let's check if this is the case. CE CE Display message is motor error. It may indicate an issue with the motor or the wiring harness between the motor and control board. This can usually be corrected by performaning the following steps: 1. Power button to turn the dishwasher off 2. Turn the circuit breaker to the dishwasher OFF and wait 10 seconds. 3. Turn the circuit breaker yo the dishwasher back ON. 4.Press the POWER button to turn the dishwasher ON, and ...
Post a Comment
Read more

Indesit Dishwasher Error Codes

  Error Codes Problem A01 Water in base. Leaking. A02 Solenoid. Valve failure. A03 Failure to drain (time). Faulty pump or blockage preventing drain. A04 NTC. NTC faulty. A05 Filters blocked. Filter cleaning cycle failed. A06 Fill failure. No water intake or valve faulty. A08 Heating failure. Thermistor not attached or faulty. A09 Software. Replace PCB. A10 Element. Heating element open circuit. A12 Hardware. Display module comms error. A13 Dispenser Triac fault, Wash Cycle completes but with Dispenser Lid not functioning correctly. H20 Static ‘Fill Time exceeding 6 minutes. Indesit Dishwasher Overall View Indesit Dishwasher Overall View Troubleshooting Whenever the appliance fails to work, check for a solution from the following list before calling for Assistance. Problem Possible causes / Solutions The dishwasher does not start or cannot be controlled. 1.Switch off the appliance by pressing the ON/OFF button, switch it back on after approximately one minute and reset the program....
Post a Comment
Read more

Fisher Paykel Dishwasher Error Codes

  Error Codes Problem A1 No water-the water supply hasn’t been turned on. A6 The spray arm has loosened or come off its mounting, or water pressure is too low. F2X Motor fault. F3X Temperature fault. You may need to have a tempering valve installed on your water supply, to ensure that incoming water is less than 65C (149F). F4X Heating element failed. F5X Fault with the internal lid of the dishwasher. F6X Component failure. F7X Fill valve fault. F8X Electronics fault-motor controller. F9X Electronics fault-wash controller. FCX Electronics fault-communication between drawers. F1 Flood switch has been activated. Turn the water and power supply to the DishDrawer off and call your Authorised Service Centre or Customer Care. F2 Motor problem. F3 Temperature sensor failed. Ensure water coming in through the inlet hose is less than 65 C. You may need to install a tempering valve on your water supply. F4 Faulty temperature sensor or element. F5 Lid fault. Turn power supply to DishDrawer® o...
Post a Comment
Read more