Skip to main content

IFB Dishwasher Error Codes

 IFB Dishwasher Error Codes


Failure Codes And What To Do In Case Of Failure;

Error CodesMeaning
F1Alarm is active against water overflow. Power off your machine and close the tap. Contact the service.
F2The waste water in the machine cannot be discharged. 1-Water discharge hose is clogged. 2-The filters of your machine might be clogged. 3-Power off-on your machine and activate the program cancellation command. 4-If the error continues, contact the service.
F3Error of continuous water input. Close the tap.
F5Inadequate water supply. 1-Make sure the water input tap is totally open and that there is no water cut. 2-Close the water input tap, separate the water input hose from the tap and clean the filter at the connection end of the hose. 3-Restart your machine, contact the service if the error resumes.
F6Faulty heater sensor.
F7Overheating error (temperature in the machine is too high)
F8Heater error.
F9Divisor position error.
FEFaulty electronic card.
FFInadequate water supply. -Make sure the water input tap is totally open and that there is no water cut. -Close the water input tap, separate the water input hose from the tap and clean the filter at the connection end of the hose. -Restart your machine, contact the service if the error resumes.

IFB Dishwasher Troubleshooting

 

IFB Dishwasher Troubleshooting
IFB Dishwasher Troubleshooting

If one of program monitor lights is on and start/Pause light is on and off,

Your machine’s door is open, shut the door.

If the programme won’t start

  • Check if the plug is connected.
  • Check your indoor fuses.
  • Be sure that the water inlet tap is turned on.
  • Be sure that you have closed the machine door.
  • Be sure that you switched off the machine by pressing the Power On / Off button.
  • Be sure that the water inlet filter and the machine filters are not clogged

If the control lamps won’t go out after a wash operation

The Power On/Off button is released yet.

If detergent residues are left in the detergent compartment

Detergent has been added when the detergent compartment was wet.

If water is left inside the machine at the end of the programme

  • The water drain hose is clogged or twisted.
  • The filters are clogged.
  • The programme is not finished yet.

If the machine stops during a wash operation

  • Power failure.
  • Water inlet failure.
  • Program can be on standby mode

If shaking and hitting noises are heard during a wash operation

  • Dishes placed incorrectly.
  • Spray arm hitting the dishes

If there are partial food wastes left on the dishes

  • Dishes placed incorrectly into the machine, sprayed water did not reach related places.
  • Basket overly loaded.
  • Dishes leaning against one another.
  • Very small amount of detergent added.
  • An unsuitable, rather weak wash programme selected.
  • Spray arm clogged with food wastes.
  • Filters clogged.
  • Filters incorrectly fitted.
  • Water drain pump clogged

If there are whitish stains on the dishes

  • A very small amount of detergent is being used.
  • Rinse aid dosage setting at a very low level.
  • No special salt is being used despite the high degree of water hardness.
  • Water softener system setting is at a very low level.
  • Salt compartment cap not closed well.
  • A detergent without phospate used; try one that contains phosphate.

If the dishes won’t dry up

  • A programme without a dry operation selected.
  • Rinse aid dosage set too lo
  • Dishes unloaded too fast

If there are rust stains on the dishes

  • Stainless-steel quality of the dishes washed is insufficient.
  • High rate of salt in the wash water.
  • Salt compartment cap not closed well.
  • Too much salt spilt into the sides and into the machine while filling it with salt.
  • Unhealthy mains grounding.

IFB Dishwasher Washing, End, Start Pause Button Flashing

FailureFailure Description
Start Pause button flashingInadequate water supply.
End button flashingError of continuous water input.
Start and End button flashingThe waste water in the machine cannot be discharged.
Washing and Start button flashingIntended water temperature could not be reached faulty heater and heater sensor.
Washing and End button flashingAlarm is active against water overflow.
Washing, End, Start button flashingFaulty electronic card.

IFB Dishwasher Manual PDF

Comments

Post a Comment

Popular posts from this blog

LG Dishwasher Error Codes

  Troubleshooting according to displayed error message: Error Message Meaning 2H Estimated Time. A 2H is only an indicator of the estimated time remainging for cycle. 2H means the estimated time remaing is less than 2 hours, when the time is less than 99 minutes, is starts counting down untill the washing cycle is over. This is not an error code and does not require a repair service. AE AE Error code indicates a possible leak from the unit. This is most often caused by excessive suds overflowing into the base of the dishwasher. Let's check if this is the case. CE CE Display message is motor error. It may indicate an issue with the motor or the wiring harness between the motor and control board. This can usually be corrected by performaning the following steps: 1. Power button to turn the dishwasher off 2. Turn the circuit breaker to the dishwasher OFF and wait 10 seconds. 3. Turn the circuit breaker yo the dishwasher back ON. 4.Press the POWER button to turn the dishwasher ON, and ...
Post a Comment
Read more

Samsung Dishwasher Error Codes

  Information codes are displayed to help you better understand what is occurring with your dishwasher. If any of the codes below occur, you should select the Reset option and follow the respective instruction. Error Codes Meaning 4E Water Supply Error. 1. When the pulse of 100 or less is detected 1 minute after the water supply starts. 2. When flow meter pulse is 5 or less 5 seconds after the water supply starts. 3. No water detected 5 min after start. 4E1 Water Supply Error. When 80C or above is detected during water supply. tE Temperature sensor error. When 0.2V or below, or 4.5V or above is maintained for over 3 seconds. tE1 Temp Sensor Error. When 0.2V or below, or 4.5V or above is maintained for over 3 seconds. 5E Drain Error. When OFF status of Low Level S/W is not detected within3 minutes during the drain oE Overflow Error. When overflow detection AD data is 4.0V or below for 3 seconds (When leakage sensor detects 4.0V or below for 1 seconds during water supply) LE Leakage ...
Post a Comment
Read more

Indesit Dishwasher Error Codes

  Error Codes Problem A01 Water in base. Leaking. A02 Solenoid. Valve failure. A03 Failure to drain (time). Faulty pump or blockage preventing drain. A04 NTC. NTC faulty. A05 Filters blocked. Filter cleaning cycle failed. A06 Fill failure. No water intake or valve faulty. A08 Heating failure. Thermistor not attached or faulty. A09 Software. Replace PCB. A10 Element. Heating element open circuit. A12 Hardware. Display module comms error. A13 Dispenser Triac fault, Wash Cycle completes but with Dispenser Lid not functioning correctly. H20 Static ‘Fill Time exceeding 6 minutes. Indesit Dishwasher Overall View Indesit Dishwasher Overall View Troubleshooting Whenever the appliance fails to work, check for a solution from the following list before calling for Assistance. Problem Possible causes / Solutions The dishwasher does not start or cannot be controlled. 1.Switch off the appliance by pressing the ON/OFF button, switch it back on after approximately one minute and reset the program....
Post a Comment
Read more