Skip to main content

Indesit Dishwasher Error Codes

 Indesit Dishwasher Error Codes

Error CodesProblem
A01Water in base. Leaking.
A02Solenoid. Valve failure.
A03Failure to drain (time). Faulty pump or blockage preventing drain.
A04NTC. NTC faulty.
A05Filters blocked. Filter cleaning cycle failed.
A06Fill failure. No water intake or valve faulty.
A08Heating failure. Thermistor not attached or faulty.
A09Software. Replace PCB.
A10Element. Heating element open circuit.
A12Hardware. Display module comms error.
A13Dispenser Triac fault, Wash Cycle completes but with Dispenser Lid not functioning correctly.
H20Static ‘Fill Time exceeding 6 minutes.

Indesit Dishwasher Overall View

Indesit Dishwasher Overall View
Indesit Dishwasher Overall View

Troubleshooting

Whenever the appliance fails to work, check for a solution from the following list before calling for Assistance.

ProblemPossible causes / Solutions
The dishwasher does not start or cannot be controlled.1.Switch off the appliance by pressing the ON/OFF button, switch it back on after approximately one minute and reset the program. 2.The appliance has not been plugged in properly. 3.The dishwasher door has not been shut properly.
The door won’t close.The lock was released. Strongly push the door until a “clacking” noise is heard.
No water drains from the dishwasher.1.The dishwasher cycle has not finished yet. 2.The water drain hose is bent (see Installation). 3.The drain duct is blocked. 4.The filter is clogged up with food residues.
The dishwasher is too noisy.1.The dishes are rattling against each other or against the sprayer arms. 2.An excessive amount of foam has been produced: the detergent has not been measured out correctly or it is not suitable for use in dishwashers.
The dishes and glasses are covered in a white film or limescale deposits.1.The level of refined salt is low or the dosage setting is not suited to the hardness of the water (see Rinse aid and salt.) 2.The lid on the salt dispenser was not closed properly. 3.The rinse aid has been used up or the dosage is too low
The dishes and glasses are streaked or have a bluish tinge.The rinse aid dosage is too high.
The crockery has not been dried properly.1.A wash cycle without a drying cycle has been selected. 2.The rinse aid has been used up or the dosage is too low. 3.The rinse aid setting is not suitable. 4.The crockery is made from non-stick material or plastic
The dishwasher does not take any water in - Tap shut-off alarm.1.There is no water in the mains supply. 2.The water inlet hose is bent. 3.Turn on the tap and the appliance will start after a few minutes.
The crockery is not clean.1.The racks are overloaded. 2.The crockery has not been arranged properly. 3.The sprayer arms cannot move freely. 4.The wash cycle is too gentle.

Indesit Dishwasher Manual PDF

Comments

Post a Comment

Popular posts from this blog

LG Dishwasher Error Codes

  Troubleshooting according to displayed error message: Error Message Meaning 2H Estimated Time. A 2H is only an indicator of the estimated time remainging for cycle. 2H means the estimated time remaing is less than 2 hours, when the time is less than 99 minutes, is starts counting down untill the washing cycle is over. This is not an error code and does not require a repair service. AE AE Error code indicates a possible leak from the unit. This is most often caused by excessive suds overflowing into the base of the dishwasher. Let's check if this is the case. CE CE Display message is motor error. It may indicate an issue with the motor or the wiring harness between the motor and control board. This can usually be corrected by performaning the following steps: 1. Power button to turn the dishwasher off 2. Turn the circuit breaker to the dishwasher OFF and wait 10 seconds. 3. Turn the circuit breaker yo the dishwasher back ON. 4.Press the POWER button to turn the dishwasher ON, and ...
Post a Comment
Read more

Samsung Dishwasher Error Codes

  Information codes are displayed to help you better understand what is occurring with your dishwasher. If any of the codes below occur, you should select the Reset option and follow the respective instruction. Error Codes Meaning 4E Water Supply Error. 1. When the pulse of 100 or less is detected 1 minute after the water supply starts. 2. When flow meter pulse is 5 or less 5 seconds after the water supply starts. 3. No water detected 5 min after start. 4E1 Water Supply Error. When 80C or above is detected during water supply. tE Temperature sensor error. When 0.2V or below, or 4.5V or above is maintained for over 3 seconds. tE1 Temp Sensor Error. When 0.2V or below, or 4.5V or above is maintained for over 3 seconds. 5E Drain Error. When OFF status of Low Level S/W is not detected within3 minutes during the drain oE Overflow Error. When overflow detection AD data is 4.0V or below for 3 seconds (When leakage sensor detects 4.0V or below for 1 seconds during water supply) LE Leakage ...
Post a Comment
Read more