Skip to main content

Zanussi Dishwasher Error Codes

 Zanussi Dishwasher Error Codes

Error CodesSolution
i30Error message i30 indicates a leak and / or water collecting at the bottom of the appliance.
i60Reset your appliance. If the cycle starts and operates normally, the problem has been resolved.
i80Reset your appliance. Check whether the appliance displays the same error message again or whether it has changed.
iC3Reset your appliance.
iC2Reset your appliance.
iC1Reset your appliance.
iCoReset your appliance.
iC0Reset your appliance.
BloDishwasher shows “BLO” on the display. It indicates that the child safety lock ("Blocking") is active. To deactivate, press the "Short" and "Prewash" buttons simultaneously.
Dishwasher beeps 3 times or the LED flashes 3 timesReset your appliance.
Cycle indicator light is flashing on the dishwasher
Cycle indicator light is flashing on the dishwasher. Cancel the previous cycle before programming a new one.
i51, i52, i53, i54, i55, i56, i57, i58, i59, i5A, i5B (i5H), i5C, i5D, i5E, i5FReset your appliance.
Zanussi Dishwasher - Description of the appliance
Zanussi Dishwasher – Description of the appliance

How to reset dishwasher?

  • Remove the plug for the dishwasher, wait 1 minute and plug it back in.
  • You can also turn off the power using the fuses on the panel/power switch.
  • If you have pulled the machine out and then pushed it back into position, it is important to ensure that no tubing is kinked or crushed and that the tap is fully open.
  • Turn on the dishwasher, select a suitable cycle and start it.
  • If the cycle starts and operates normally, the problem has been resolved.
Zanussi Dishwasher Control Panel
Zanussi Dishwasher Control Panel

Zanussi Dishwasher Troubleshooting

Certain problems are due to the lack of simple maintenance or oversights, which can be solved with the help of the instructions given here, without calling out an engineer. The dishwasher will not start or stops during operation. Press the On/Off push button to switch the dishwasher off and carry out the following suggested corrective actions.

TroublePossible causeSolutions
The programme does not startThe dishwasher door has not been properly closed.Close the door.
The main plug is not plugged inInsert the mains plug.
The fuse has blown in the household fuse box.
Replace the fuse.
The machine does not fill with water.The water tap is blocked or furred with limescale.Clean the water tap
The water tap is turned off.Turn the water tap on.
The filter (where present) in the threaded hose fitting at the water inlet valve is blocked.Clean the filter in the threaded hose fitting.
The water inlet hose has not been correctly laid or it is bent or squashed.Check the water inlet hose connection.
The dishwasher will not drain.The siphon is blocked.Clean out the siphon.
The water drain hose has not been correctly laid or it is bent or squashed.Check the water drain hose connection.
There is a whistling noise during washingThe whistling is not a cause for concern.Use a different brand of detergent.

Once the checks have been carried out, press the On/Off push button, the programme will continue from the point in which it was interrupted. If the problem reappears contact the consumer services department.

Zanussi Dishwasher Manual PDF

Comments

Post a Comment

Popular posts from this blog

LG Dishwasher Error Codes

  Troubleshooting according to displayed error message: Error Message Meaning 2H Estimated Time. A 2H is only an indicator of the estimated time remainging for cycle. 2H means the estimated time remaing is less than 2 hours, when the time is less than 99 minutes, is starts counting down untill the washing cycle is over. This is not an error code and does not require a repair service. AE AE Error code indicates a possible leak from the unit. This is most often caused by excessive suds overflowing into the base of the dishwasher. Let's check if this is the case. CE CE Display message is motor error. It may indicate an issue with the motor or the wiring harness between the motor and control board. This can usually be corrected by performaning the following steps: 1. Power button to turn the dishwasher off 2. Turn the circuit breaker to the dishwasher OFF and wait 10 seconds. 3. Turn the circuit breaker yo the dishwasher back ON. 4.Press the POWER button to turn the dishwasher ON, and ...
Post a Comment
Read more

Siemens Dishwasher Error Codes

  Experience has shown that you can rectify  most faults  which occur in daily operation yourself. This ensures that the appliance is quickly available to you again. In the following overview you can find  possible causes  of malfunctions and helpful information for rectifying them. Error Codes Problem E01, E02, E03, E04, E05 Your dishwasher is showing a dishwasher error code relating to faulty electronics. This probably means a technical error has occurred or the programme has been interrupted. Your dishwasher might need repairing. Solution: Before you contact Siemens Service, restart your dishwasher. To do this, please switch off the appliance using the on/off switch, wait a few minutes, then restart the appliance. If the dishwasher error code is still there, close the water tap and disconnect the dishwasher from the power supply. E6 The dishwasher has detected a faulty door sensor or faulty electronics. E7 There is a fault in the dishwasher’s drying system. E...
Post a Comment
Read more

Samsung Dishwasher Error Codes

  Information codes are displayed to help you better understand what is occurring with your dishwasher. If any of the codes below occur, you should select the Reset option and follow the respective instruction. Error Codes Meaning 4E Water Supply Error. 1. When the pulse of 100 or less is detected 1 minute after the water supply starts. 2. When flow meter pulse is 5 or less 5 seconds after the water supply starts. 3. No water detected 5 min after start. 4E1 Water Supply Error. When 80C or above is detected during water supply. tE Temperature sensor error. When 0.2V or below, or 4.5V or above is maintained for over 3 seconds. tE1 Temp Sensor Error. When 0.2V or below, or 4.5V or above is maintained for over 3 seconds. 5E Drain Error. When OFF status of Low Level S/W is not detected within3 minutes during the drain oE Overflow Error. When overflow detection AD data is 4.0V or below for 3 seconds (When leakage sensor detects 4.0V or below for 1 seconds during water supply) LE Leakage ...
Post a Comment
Read more