| Error | Solution |
|---|---|
| E01 | No feedback signal from door interlock. After 15 seconds the E01 code is displayed and the wash programme is terminated. |
| E02 | 2 Filling time longer than 2 minutes The “Ready” LED flashes during the wash (which is not terminated). After the washing is completed the E02 error code is displayed. Further fillings above the pressure controller level are blocked. - Low mains water pressure -Partia||y blocked inlet hose or valves . |
| 4th program led | 3 Way Valve Position Error. Possible Causes: a. Malfunction of 3W Valve b. Disconnection on the lines between the electronics and the 3W Valve |
| 3rd Program Led | NTC Fault. At the Heating step, if NTC resistance is measured as open / short circuit or beyond the specified resistance values, then NTC fault can be detected. Possible Causes: a. Malfunction of NTC b. Crack on the connection lines between electronics and NTC |
| 3rd Program Led | Heating Fault. Possible Causes: a. Malfunction of Heater b. Crack on the connection lines between electronics and heater c. Malfunction of RL1 relay on the electronic board d. Too less water inside the machine |
| 2rd Program Led | No Water and Counter Fault . Possible Causes: a. Malfunction of Water Inlet Valve b. Malfunction of Water Counter c. Crack on the connection lines between the electronics and water inlet valve d. Crack on the connection lines between the electronics and water counter |
| 1 st Program Led | Uninterruptible Water Inlet Error. Possible Causes: a. Malfunction of Water-Inlet Valve (stuck as open) b. Malfunction of T7 triac on the electronic board |
| Machine does not start | Power cable is unplugged. >>> Check if the power cable is plugged in. |
| Dishes are not washed clean | Filters are clogged. >>> Check if the filter system is clean. Clean the filter system regularly as illustrated in section “Cleaning and Care”. |
| Dishes are not dry at the end of cycle | Dishes are not placed orderly in the machine. >>> Place your dishes in a way that no water will accumulate in them. |
| Tea, cafe or lipstick stains remain on dishes. | Selected programme is unsuitable. >>> Select a programme with a higher temperature and cycle time. |
| Lime traces remain on dishes and glassware gains a misty appearance | Rinse aid is not sufficient. >>> Check the rinse aid indicator and add rinse aid if necessary. Increase the rinse aid setting if there is enough amount of rinse aid in the machine. |
| There is a different odour in the machine | Filters are clogged. >>> Check if the filter system is clean. Clean the filter system regularly as illustrated in section “Cleaning and Care”. |
| Rust, discoloration or surface deterioration occurs on dishes | Salt leakage exists. >>> Salt may cause deterioration and oxidation on metal surfaces. Pay attention not to spill salt around the salt filling hole while adding salt. Make sure that the salt reservoir lid is tightly closed after finishing the filling process. Run the prewash programme to remove the salt that spilled inside the machine. Since the salt granules that will remain under the lid will dissolve during prewash, causing the lid loosen, check the lid once again at the end of the programme. |
| Detergent remains in detergent dispenser. | Detergent dispenser was damp when adding detergent. >>> Make sure that the detergent dispenser is dried well prior to filling it with detergent. |
Draın Hose, Water Inlet Valve, And Clıp Box
To render services to these components, the operators should work on the backside of the machine. The concrete sheet should be removed. The hose holder is taken out by turning as it is seen in the picture.
Blomberg Dishwasher – Operating The Dishwasher
Blomberg Dishwasher – Cleaning The Hose Filter
Damages on the machine that may be caused by impurities coming from the urban supply water or your own water installation (such as sand, dirt, rust, etc.) can be prevented by means of the filter attached to the water inlet hose. Check the filter and the hose regularly and clean them if necessary.
- Turn off the tap and remove the hose.
- After taking out the filter, clean it under running tap water.
- Place the cleaned filter back to its seat in the hose.
- Install the hose to tap.
Blomberg Dishwasher – Cleaning The Filters
Clean the filters at least once a week in order for the machine operates efficiently. Check if food residues are left on the filters. If there are food residues on filters, take them out and clean well under running water.
- Turn the micro filter (1) and coarse filter (2) assembly counterclockwise and pull it out from its seating (A)
- Pull out the metal / plastic filter (3) from the seating (C).
- Press the two pawls on the coarse filter inwards and separate the coarse filter from the assembly (B).
- Clean all three filters under tap water by means of a brush.
- Replace the metal/plastic filter.
- Place the coarse filter into the microfilter. Make sure that it is properly seated. Turn the coarse filter clockwise until a “click” sound is heard.
Comments
Post a Comment