Skip to main content

Frigidaire Dishwasher Error Codes

 Frigidaire Dishwasher Error Codes

Error CodesSolution
i10A low fill has been detected. Look for a pinched water supply line, or water shutoff is not completely opened.
i20Clogged filters or a restricted drain line has been detected. Check and clean both filters and sump area and check for a pinched or blocked drain hose. If the drain line is attached to a disposer, check that the knockout plug has been removed.
i40Clogged filters or a restricted drain line has been detected. Check and clean both filters and sump area and check for a pinched or blocked drain hose. If the drain line is attached to a disposer, check that the knockout plug has been removed.
iF0Clogged filters or a restricted drain line has been detected. Check and clean both filters and sump area and check for a pinched or blocked drain hose. If the drain line is attached to a disposer, check that the knockout plug has been removed.
i30A leak or over flow of water has been detected in the bottom pan. Look for loose connections at the water inlet valve and ensure the unit is properly leveled.
i50A problem has been detected with the drain or wash motor. Pressing the cancel button or turning power off at the breaker for 5 minutes should clear this error code and the unit can be restarted.
i60A problem has been detected with the water heating system. Pressing the cancel button or turning power off at the breaker for 5 minutes should clear this error code and the unit can be restarted.
iC0A problem has been detected with the electronic control system. Pressing the cancel button or turning power off at the breaker for 5 minutes should clear this error code and the unit can be restarted.
UOVent open. While in wash cycle, Main Control Board does not receive signal from vent assembly that vent plunger is closed. Plunger status is sensed with optical sensor in vent assembly. Check wiring between vent assembly and Main Control Board. If wiring correct, replace vent assembly. If error still exist, replace Main Control Board.
UFFan not running. While in drying cycle, Main Control Board not sensing vent fan motor rotation at correct speed. Check wiring between vent assembly and Main Control Board. If correct, replace vent assembly. If error still exist replace Main Control Board.
ERMembrane Switch Failure. Main Control Board has detected a stuck key or a key pressed for more than one minute. Check connection from keypad to Main Control Board. If correct, replace keypad. If error still exist, replace Main Control Board.
CEConfiguration Error. Check wiring connections between keypad and Main Control Board. Check for correct parts installed. Replace parts accordingly.
CLClose Door – Door Switch Open. Main Control Board not sensing door closed. Close door. Check door switches. Check wiring between door switches and Main Control Board. If wiring and switches are correct, replace Main Control Board.
dPDrain Pump. Displayed in relay test when drain pump is activated.
Frigidaire Dishwasher Parts
Frigidaire Dishwasher Parts

Troubleshooting

Before calling for service, review this list. It may save you both time and expense. This list includes common experiences that are not the result of defective workmanship or material in your dishwasher.

Food Soils Left on Dishes

  1. Choose another cycle for longer washing time.
  2. Choose the Hi-Temp Wash option.
  3. Check rack loading section for proper loading-avoid nesting items.
  4. Home water pressure may be too low – should be 20 to 120 pounds per square inch (psi).
  5. Check incoming water temperature. It should be at least 120oF (49oC). (See Factors Affecting Performance.)
  6. Check water hardness. For extremely hard water, it may be necessary to install a water softener. (See Detergent Chart).
  7. Use Fresh Detergent.
  8. Make sure items are not blocking the spray arms, preventing them from rotating.

Dishes not Dry

  1. Select heat dry option.
  2. Make sure the rinse aid dispenser is filled.
  3. Increase the discharge setting of rinse aid. (See Rinse Aid).
  4. Check the incoming water temperature. Be sure it is at least 120F (49oC).
  5. Check for proper loading-avoid nesting items.
  6. Plastic items may need to be towel dried.
  7. Cups with a concave bottom will collect water. Load them at the far left of the upper rack so they will be held in a tilted position.

Glassware/Flatware Spotted or Cloudy

  1. Check water hardness. For extremely hard water, it may be necessary to install a water softener.
  2. Water temperature may be low. Avoid extremely low or high temperatures.
  3. Avoid overloading and improper loading.
  4. Use fresh detergent. Old detergent is ineffective.
  5. Make sure rinse aid dispenser is filled.
  6. Check to see that proper amount of detergent is being used for cycle selected. Also, check phosphate level.
  7. Home water pressure may be too low – it should be 20 to 120 pounds per square inch (psi).

Dishware Chipped

  1. Load with care and do not overload. (See Preparing and Loading Dishes).
  2. Place delicate items in top rack.
  3. Place glasses securely against pins and not over pins.
  4. Load items so they are secure and don’t jar loose when moving racks in and out. Move racks in and out slowly.
  5. Make sure tall glasses and stemware will clear top of tub when rack is pushed in.
  6. Fine antique china and crystal should be hand-washed.

Detergent Left in Dispenser Cup

  1. Detergent may be old. Discard and use fresh detergent.
  2. Be sure the dish load doesn’t block spray from entering the detergent cup.
  3. Check to see if cycle has been completed.
  4. Make sure items do not prevent the detergent dispenser from opening.

Dishwasher Won’t Run

  1. Check to see if circuit breaker is tripped or if a fuse is blown.
  2. Make sure water supply is turned on.
  3. Check to see if cycle is set correctly.
  4. Is dishwasher set for Delay Start Option?
  5. Make sure door is closed and latched.

Dishwasher Does Not Drain Properly

  1. If unit is hooked up to a food waste disposer, make sure the disposer is empty.
  2. Check to see if the knockout plug has been removed from inside the food waste disposer inlet.
  3. Check to see if drain hose is kinked.
  4. Make sure cycle is complete, not in a pause.

Frigidaire Dishwasher Manual PDF

Comments

Post a Comment

Popular posts from this blog

LG Dishwasher Error Codes

  Troubleshooting according to displayed error message: Error Message Meaning 2H Estimated Time. A 2H is only an indicator of the estimated time remainging for cycle. 2H means the estimated time remaing is less than 2 hours, when the time is less than 99 minutes, is starts counting down untill the washing cycle is over. This is not an error code and does not require a repair service. AE AE Error code indicates a possible leak from the unit. This is most often caused by excessive suds overflowing into the base of the dishwasher. Let's check if this is the case. CE CE Display message is motor error. It may indicate an issue with the motor or the wiring harness between the motor and control board. This can usually be corrected by performaning the following steps: 1. Power button to turn the dishwasher off 2. Turn the circuit breaker to the dishwasher OFF and wait 10 seconds. 3. Turn the circuit breaker yo the dishwasher back ON. 4.Press the POWER button to turn the dishwasher ON, and ...
Post a Comment
Read more

Siemens Dishwasher Error Codes

  Experience has shown that you can rectify  most faults  which occur in daily operation yourself. This ensures that the appliance is quickly available to you again. In the following overview you can find  possible causes  of malfunctions and helpful information for rectifying them. Error Codes Problem E01, E02, E03, E04, E05 Your dishwasher is showing a dishwasher error code relating to faulty electronics. This probably means a technical error has occurred or the programme has been interrupted. Your dishwasher might need repairing. Solution: Before you contact Siemens Service, restart your dishwasher. To do this, please switch off the appliance using the on/off switch, wait a few minutes, then restart the appliance. If the dishwasher error code is still there, close the water tap and disconnect the dishwasher from the power supply. E6 The dishwasher has detected a faulty door sensor or faulty electronics. E7 There is a fault in the dishwasher’s drying system. E...
Post a Comment
Read more

Samsung Dishwasher Error Codes

  Information codes are displayed to help you better understand what is occurring with your dishwasher. If any of the codes below occur, you should select the Reset option and follow the respective instruction. Error Codes Meaning 4E Water Supply Error. 1. When the pulse of 100 or less is detected 1 minute after the water supply starts. 2. When flow meter pulse is 5 or less 5 seconds after the water supply starts. 3. No water detected 5 min after start. 4E1 Water Supply Error. When 80C or above is detected during water supply. tE Temperature sensor error. When 0.2V or below, or 4.5V or above is maintained for over 3 seconds. tE1 Temp Sensor Error. When 0.2V or below, or 4.5V or above is maintained for over 3 seconds. 5E Drain Error. When OFF status of Low Level S/W is not detected within3 minutes during the drain oE Overflow Error. When overflow detection AD data is 4.0V or below for 3 seconds (When leakage sensor detects 4.0V or below for 1 seconds during water supply) LE Leakage ...
Post a Comment
Read more