Skip to main content

Amica Dishwasher Error Codes

 Amica Dishwasher Error Codes

When some malfunctions come on, the appliance will display error codes to warn you:
Error CodesSolution
E1Water supply timeout. • Closed water valve. • Clogged water pipe • Water pressure too low • If error persists contact customer service.
E4Overflow. • Water level too high • If error persists contact customer service.
The Rapid light flicker fleetlyLonger inlet time. Faucets is not opened, or water intake is restricted,or water pressure is too low.
The Glass light flicker fleetlyOverflow. Some element of dishwasher leaks.
amica-dishwasher-flashing-lights
Amica Dishwasher Flashing Lights

If one of program monitor lights is on and start/Pause light is on and off,

Your machine’s door is open, shut the door.

If the programme won’t start

  • Check if the plug is connected.
  • Check your indoor fuses.
  • Be sure that the water inlet tap is turned on.
  • Be sure that you have closed the machine door.
  • Be sure that you switched off the machine by pressing the Power On / Off button.
  • Be sure that the water inlet filter and the machine filters are not clogged.

If the lamps “Wash/Dry” and “End” keep flashing

  • Water overflow alarm is active
  • Turn off your tap and contact an authorised service.

If the control lamps won’t go out after a wash operation

The Power On/Off button is released yet.

If detergent residues are left in the detergent compartment

Detergent has been added when the detergent compartment was wet.

If water is left inside the machine at the end of the programme

  • The water drain hose is clogged or twisted.
  • The filters are clogged.
  • The programme is not finished yet.

If the machine stops during a wash operation

  • Power failure.
  • Water inlet failure.
  • Program can be on standby mode.

Amica Dishwasher Troubleshooting

Amica Dishwasher Troubleshooting
Amica Dishwasher Troubleshooting
ProblemPossible Causes
Dishwasher doesn't startFuse blown, or the circuit breaker acted
Power supply is not turned on
Water pressure is low
Door of dishwasher not properly closed.
Water not pumped form dishwasherKink in drain hose
Filter clogged
Kitchen sink clogged
Suds in the tubImproper detergent
Spilled rinse-aid
Stained tub interiorDetergent with colourant was used. Make sure that the detergent is the one without colourant.
White film on inside surfaceHard water minerals. To clean the interior, use a damp sponge with dishwasher detergent and wear rubber gloves. Never use any other cleaner than dishwasher detergent for the risk of foaming or suds.
There are rust stains on cutleryThe affected items are not corrosion resistant.
A programme was not run after dishwasher salt was added. Traces of salt have gotten into the wash cycle.
The lid of the softer is loose. Check the lip .Ensure the fix is fine.
Knocking noise inthe wash cabinetA sp ay arm is knocking against an item in a basket. Interrupt the programme, and rearrange the items which are obstructing the sp ay arm.
Rattling noise in the wash cabinetItems of crockery are loose in the wash cabinet. Interrupt the programme, and rearrange the items of crockery.
Knocking noise in the water pipesThis may be caused by on-site installation or the cross-section of the piping. This has no influence on the dishwasher function. if in doubt, contact a suitably qualified plumber.

Amica Dishwasher Manual PDF

Comments

Post a Comment

Popular posts from this blog

LG Dishwasher Error Codes

  Troubleshooting according to displayed error message: Error Message Meaning 2H Estimated Time. A 2H is only an indicator of the estimated time remainging for cycle. 2H means the estimated time remaing is less than 2 hours, when the time is less than 99 minutes, is starts counting down untill the washing cycle is over. This is not an error code and does not require a repair service. AE AE Error code indicates a possible leak from the unit. This is most often caused by excessive suds overflowing into the base of the dishwasher. Let's check if this is the case. CE CE Display message is motor error. It may indicate an issue with the motor or the wiring harness between the motor and control board. This can usually be corrected by performaning the following steps: 1. Power button to turn the dishwasher off 2. Turn the circuit breaker to the dishwasher OFF and wait 10 seconds. 3. Turn the circuit breaker yo the dishwasher back ON. 4.Press the POWER button to turn the dishwasher ON, and ...
Post a Comment
Read more

Indesit Dishwasher Error Codes

  Error Codes Problem A01 Water in base. Leaking. A02 Solenoid. Valve failure. A03 Failure to drain (time). Faulty pump or blockage preventing drain. A04 NTC. NTC faulty. A05 Filters blocked. Filter cleaning cycle failed. A06 Fill failure. No water intake or valve faulty. A08 Heating failure. Thermistor not attached or faulty. A09 Software. Replace PCB. A10 Element. Heating element open circuit. A12 Hardware. Display module comms error. A13 Dispenser Triac fault, Wash Cycle completes but with Dispenser Lid not functioning correctly. H20 Static ‘Fill Time exceeding 6 minutes. Indesit Dishwasher Overall View Indesit Dishwasher Overall View Troubleshooting Whenever the appliance fails to work, check for a solution from the following list before calling for Assistance. Problem Possible causes / Solutions The dishwasher does not start or cannot be controlled. 1.Switch off the appliance by pressing the ON/OFF button, switch it back on after approximately one minute and reset the program....
Post a Comment
Read more

Fisher Paykel Dishwasher Error Codes

  Error Codes Problem A1 No water-the water supply hasn’t been turned on. A6 The spray arm has loosened or come off its mounting, or water pressure is too low. F2X Motor fault. F3X Temperature fault. You may need to have a tempering valve installed on your water supply, to ensure that incoming water is less than 65C (149F). F4X Heating element failed. F5X Fault with the internal lid of the dishwasher. F6X Component failure. F7X Fill valve fault. F8X Electronics fault-motor controller. F9X Electronics fault-wash controller. FCX Electronics fault-communication between drawers. F1 Flood switch has been activated. Turn the water and power supply to the DishDrawer off and call your Authorised Service Centre or Customer Care. F2 Motor problem. F3 Temperature sensor failed. Ensure water coming in through the inlet hose is less than 65 C. You may need to install a tempering valve on your water supply. F4 Faulty temperature sensor or element. F5 Lid fault. Turn power supply to DishDrawer® o...
Post a Comment
Read more